Swimn-play Slim Style Oval Pool Manual do Utilizador

Part# 420870-16 GENERALInstallation of this above ground pool is not extremely hard or confusing, but it is a big job. The secret to installing a poo

10Unpack and assemble the supports using the steps in the following pages.3/8” - 16 x 1”HEX HEAD BOLT3/8” - 16 HEX NUT5/16” - 18 x 1/2”HEX HEAD BOLT#1

11Use the chart on page 6 to find the correct distance from C to C for your pool. Tie a string on each end from C to C, across the leveled area to cre

Start assembling the supports by placing two T-Plates inside the Bottom Support and insert and tighten the 3/8”-16 x 1” hex head bolts and 3/8”-16 he

13Center SupportPostGFInsert the Support Post between the T-Plates and through the hole in the Vertical Plate (image F).The open side of the post must

14Patio BlockTrenchCarpenter’sLevel2x4Using a 2x4 and a level, as shown, make sure that each Support Assembly is level with the next Support Assembly.

15The screws joining the straps must be inserted from the top to prevent the screw putting a hole in the liner once the pool is filled with water.STRA

16Follow the instructions below to properly layout the rail and strap assemblies.QUANTITIES NEEDED: POOL SIZE 18x12 20x12 24x12 24x15 30x15 33x18 3

Remove wall from carton. NOTE: the UP arrow on the wall.Determine starting point as the filter inlet and outlet holes are at the beginning of the wa

18 Insert the 1/4" - 20x3/4" truss head screws from inside the pool through the preattached inside closure bar, through insid

19Measure from the last strap to the outer end of the pool. Measurements in both ends should be equal. Also make sure that the sides of the pool bet

This section is designed to acquaint you with some guidelines as to the safe operation and use of your pool. DROWNING RISK • Children, espe

20IMPORTANT!! BEFORE CONTINUING WITH THIS STEP YOU MUST KNOW WHICH TYPE OF THROUGH THE WALL SKIMMER YOU WILL BE USING WITH YOUR POOL Your pool wall

Wall guard is optional.Tape wall guard (plastic sheeting) to pool wall 12" up from ground and smooth out on ground 12" from wall. This will

CAUTIONYOUR POOL IS DESIGNED TO PROVIDE AN AMPLE SAFETY MARGIN WHEN IT STANDS ON LEVEL GROUND. FOR THIS PURPOSE A SLOPE IN EXCESS OF 2 INCHES IN ANY

23 EZ HOOK LINER INSTALLATIONATTENTION: An 8 inch cove must be placed all around the inside of the pool1. Clear all sticks and sharp objects from an

24No. 12 x 1/2”Sheet Metal ScrewIf fencing or decking is to be installed, refer to the deck and fence instructions before installing the verticals. T

Insert two rails into a plate, in the same manner and using the same spacing as you have done on the bottom rail and plate assembly. Push the rails

Your pool is equipped with (3) three special warning ledges. The (1) one ledge with a large warning on top is to be installed by the entry point i

27FOLLOW THE INSTRUCTIONS BELOW FOR THE COVERS FOR YOUR PARTICULAR POOL4", 6" & 7" DELUXE TOP COVERSThese covers don’t require cage

286" & 7" TWO-PIECE FULL CONTOURED COVER Slide inside cover (the cover which will be closest to the inside of the pool) into position a

297" AND 9” TWO-PIECE WRAP AROUND COVER AND PEDESTALSlide the inside cover (the cover which will be closest to the inside of the pool) into posit

• Never permit the pool to be used unless at least one person other than the bather is present. Children must always be under careful adult s

30WRAP AROUND PEDESTAL1 - Insert the logo into the pedestal.2 - Place the pedestal onto the bottom of the vertical and align the holes on the side

31Educational programs and materials, (i.e. seminars, workshops, brochures, videos, instructional guides, etc.) are available from NSPI

32WARNING Check all the metal on the pool frame and pool wall for signs of corrosion or deterioration. Remove any corrosion and touch up with paint.

A reliable pool water test kit will help to determine the daily chlorine dosage and the acid-alkaline condition of the water. You will find in the

CONTRACT INSTALLATIONSThe manufacturer is in no way affiliated with any professional pool installer. Therefore the manufacturer can assume no respon

5SOME FRIENDSTO HELP OUTHammerKnifeTapeRake4” NailPliersCloth TapeCenter Stake2 x 4Sifted Earth or Pre Washed SandBroomPatio BlocksCarpentersLevelShov

INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembly

INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembly

8Your pool must be installed on a solid level surface. After the pool location is selected drive the two end stakes "A" into the ground and

Using the “CLEARANCE SIZE” chart on page 6, determine the clearance size for your pool.With the use of the leveling device shown and a shovel start le